Home :: Fly Fishing :: Fly Fishing Freebies :: Sinking Japanese Beetle

Sinking Japanese Beetle

Sinking Japanese Beetle
Sinking Japanese Beetle

Designed by Harrison Steeves, III

Materials Needed:
Hook:#10 - Tiemco 3769, Orvis 1641, Mustad 3906
Thread:6/0 Olive or Green
Body:Kreinik Heavy Braid; Mallard #850, Emerald #009HL
Wing Case:Copper colored Swiss Straw or rafia
Wing:Kreinik 1/8” Ribbon; Mallard #850
Head/Thorax:Kreinik Fine Braid; Chartreuse (Caddis Larva Green) #015

Tying Directions:

1. Wrap the rear half hook shank with thread.

2. Tie in Swiss Straw, use about a 4” piece. Tie in the Swiss Straw at the end of the hook, almost to the bend of the hook. Wrap thread forward to the middle of the hook shank.

3. Tie in two 9-10” strands of Kreinik Heavy Braid on each side of the hook shank. Tie them down by wrapping the thread backward to the same point at which the Swiss Straw exits the wraps. Wrap thread forward to about 1/16” behind the hook eye, half hitch (or whip finish) and cut thread.

4. Form the body of the beetle by using the overhand knot technique, passing the eye of the through the middle of the knot. Tie so that the 009HL strand form the back (top), and the 085 strands forms the belly (bottom). Use seven (7) knots to form the body on #10 hook. This will assure the proportions. When the body has been formed, tie down both body strands of material and cut. Note: When forming the knots, use PLENTY OF TENSION. If you don’t, the body looks really loose, and there won’t be enough room at the front of the hook to finish the fly.

5. Tie in the wing material, length extending back to the butt of the fly. Tie it in at the point where the body material cords were tied down and then wrap thread firmly toward, but not to the eye of the hook. Cut off the winging material piece extending forward and save for more wings. (use about a 6” piece - it’s easy tie in the correct length and then trim the forward portion. A 6 “ piece will tie a bunch of wings.)

6. Separate wing material into 2 equal halves and pull these laterally to the sides of the fly. I use a fine pair of tweezers for this, but a needle does fine.

7. Tie in about a 6” piece of Head/Thorax material - tie it in backwards to wing butts and on the side of the fly.

8. Fold Swiss Straw forward between wings to keep them separate, and tie down the Swiss Straw firmly from the wing butts almost to the hook eye. Trim to leave a small shelf of material pointing forward. Save the remainder of the Swiss Straw for more wing cases.

9. Wrap head/thorax material forward, 3-5 wraps depending upon how much space you have. After the last wrap, pull the material under the hook shank, tight into the eye of the hook and give it a couple of good thread wraps. Do not cut it.

10. At this point there is going to be some Swiss Straw visible, so tho finish the head neatly, first cock the fly at about a 45 degree angle in the vise. Bring the head/thorax material backward with the left hand and start building up the head with 6 wraps of thread. This will not only secure the head/ thorax material, but will give a neat head on the fly.
SKU freefly_06
 
Christmas Stocking Crocheted Pin
 
Silk Gauze Fairy
 
English Bouquet
Christmas Stocking Crocheted Pin
 
Silk Gauze Fairy
 
English Bouquet
 
 
 
Angel of Autumn
 
Christmas Cardinal Wreath
 
LONCHERA ABC
Angel of Autumn
 
Christmas Cardinal Wreath
 
LONCHERA ABC
 
 
 
Threadster
 
Treasure It Gold Beadlets
 
Postal de Victoriana de Cuentas para Mamá
Threadster
 
Treasure It Gold Beadlets
 
Postal de Victoriana de Cuentas para Mamá
$3.00
 
$5.79
 

Site Secured By:
SSL