Home :: Freebies :: Kids' Projects :: Glow-in-the-dark Name Bracelet

Glow-in-the-dark Name Bracelet

Glow-in-the-dark Name Bracelet
Glow-In-The-Dark Name Bracelet

Designed by: Brenda Spitzer
Skill Level: Intermediate

Materials needed:
• Kreinik 1/8” Ribbon 055F and 052F
• letter beads for your name
• two #3 embroidery needles
• scissors
• tape measure
• masking tape

Instructions:
1. 1. To make a 6-inch bracelet, cut a 72-inch length of 055F Ribbon. This will be your knotting cord. Cut a 36-inch length of 052F Braid. This will be your filler cord. Fold both cords in half. Place folded ends together and tie an overhand knot 1/2-inch from end. (See diagrams A and B)
2. Place knotted end of cords on a flat surface like a table. Tape the knot to the surface with masking tape. Make sure that knotting cords lay on the outside and filler cords on the inside.
3. Tie a series of square knots to measure 2 inches in length. (See diagram for square knot. Bring knotting cord on left across filler cords and under right knotting cord as in “C”. Then bring right knotting cord under filler cords and then through and over the loop made by left knotting cord. Now grasp the end of knotting cord that is on the left. Bring this cord under the filler cords. Grasp the end of knotting cord that is on the right. Bring it over the filler cords. Bring knotting cords through loops on both sides, pull snuggly.)
4. Thread the two center, filler cords through the needles. Add the bead for the first letter of your name to the two filler cords by threading the needles and cords through the hole of the bead. Tie two more square knots and add the next letter of your name. Repeat this process for all the letters in your name.
5. After all of the letter beads have been added, tie another series of square knots measuring two inches in length. (Note: depending on the number of letters in your name, you may want to make the series of square knots before and after your name, either longer or shorter than two inches. The overall length of the bracelet should be the same as the measurement of your own wrist.)
6. To finish the bracelet, tie the cords into three overhand knots. Trim the ends of the cord. To fasten the bracelet, push the ending knot through the beginning loop.

Printing Instructions:
To print the instructions for this project click on the on the linkabove "Printable version" and then print the page using your web browser. 

If you have trouble printing this page and would like us to send you aprinted copy send a #10 SASE to: Glow-In-The-Dark Name Bracelet, P.O. Box 1258, Parkersburg, WV 26102.

© Copyright 2005 Kreinik. May be reproduced but not sold. Kreinik ConsumerInfo: 1-800-537-2166 or www.kreinik.com.
SKU COOL01
 
: *
: *
: *
 
Rubber-stamped card:  Friends make life a little sweeter
 
Plastic Needle Safe - Small
 
Autumn Cornucopia
Rubber-stamped card: Friends make life a little sweeter
 
Plastic Needle Safe - Small
 
Autumn Cornucopia
 
$8.25
 
 
Blackwork Style Victorian House
 
Gallery of Photo Borders:  Baby Pictures
 
Iron-on Star Photo Mat
Blackwork Style Victorian House
 
Gallery of Photo Borders: Baby Pictures
 
Iron-on Star Photo Mat
 
 
 
Celebrate Mom Scrapbook Page
 
Ornament of the Month - Dove
 
Live Love
Celebrate Mom Scrapbook Page
 
Ornament of the Month - Dove
 
Live Love
$10.00
 
$4.77
 
$8.38